• Hola Invitado, Foromecanicos es el Foro de Automecanico y Autoelectronico - informacion sobre mecanica automotriz, computers, encendido y auto electronics, diagramas.

    Compra en Amazon todo para tu vehiculo

tiempo toyota previa

El esquema e indicaciones estan adjunto [ingles]
cadena de tiempo Toyota Previa 2.4L 1991/ 1997
Saludos
 

Adjuntos

  • calld915.jpg
    calld915.jpg
    74 KB · Visitas: 4.779
  • calld915A.jpg
    calld915A.jpg
    78,5 KB · Visitas: 1.412
  • calld915B.jpg
    calld915B.jpg
    80,3 KB · Visitas: 1.236
Última edición por un moderador:
Comparto instrucciones para reemplazo de Cabeza
Toyota Previa LE 2.4L 4 cil 2TZ-FZE
CYLINDER HEAD, REPLACE
1.Disconnect battery ground cable.
2.Remove engine harness cover attaching bolts, then disconnect.
3.Disconnect pressure regulator vacuum hose.
4.Disconnect the following electrical connectors:
a.Oil pressure switch.
b.Oil level sensor.
c.Distributor connector.
d.Start injector time switch.
e.On California models, EGR gas temperature sensor.
f.On all models, water temperature sensor and sender gauge.
g.Knock sensor.
h.Four injector connectors.
5.Remove No. 2 cylinder head cover.
6.Disconnect No. 2 and 3 air hoses, then remove distributor.
7.Remove EGR valve, pipe and gaskets.
8.Remove delivery pipe and cold start injector union bolts and gaskets, then pressure regulator and hose, then remove fuel pipe.
9.Remove water outlet and No. 2 water bypass pipe and gasket.
10.Remove PCV hose.
11.Remove delivery pipe.
12.Disconnect water pump hose, the remove intake manifold brackets and manifold.
13.Remove RH engine mount.
14.Remove exhaust manifold attaching nuts, then remove.
15.Remove RH engine mount.
16.Remove exhaust manifold heat insulator.
17.Remove No. 1 oil return pipe.
18.Remove No. 1 cylinder head cover, then half circular plugs.
19.Place installation alignment marks on camshaft sprocket and chain.
20.Hold camshaft, then remove cam sprocket bolt.
21.Remove chain tensioner and gasket, remove cam sprocket and chain. Do not remove slipper and damper.
22.Remove No. 6 bearing cap bolt.
23.Remove exhaust camshafts as follows:
a.Camshaft must be held level during removal or cylinder head damage may result.
b.Set exhaust knock pin hole at 5-30° BTDC, Fig. 1.
c.Install service bolt to camshaft sub-gear and main gear.
d.Alternately and uniformly loosen and remove Nos. 1, 2, 3 and 5 bearing caps in sequence shown Fig. 2.
e.Alternately and uniformly loosen No. 4 bearing cap bolt, Fig. 3, ensure camshaft is being lifted straight out, if not retighten No. 4 cap and reverse camshaft removal procedure. Do not pry or force camshaft.
f.Remove No. 4 bearing cap and exhaust camshaft.
24.Remove intake camshafts as follows:
a.Set exhaust knock pin hole at 75-100° BTDC, Fig. 4.
b.Install service bolt to camshaft sub-gear and main gear.
c.Alternately and uniformly loosen and remove Nos. 1, 2, 4 and 5 bearing caps in sequence shown Fig. 5.
d.Alternately and uniformly loosen No. 3 bearing cap bolt, Fig. 6,ensure camshaft is being lifted straight out, if not retighten No. 3 cap and reverse camshaft removal procedure. Do not pry or force camshaft.
e.Remove No. 3 bearing cap and exhaust camshaft.
25.Remove two front cylinder head bolts, then remove cylinder head bolts, in sequence Fig. 7, in two or three steps.
26.Reverse procedure to install, noting the following:
a.Torque cylinder head bolts in reverse removal sequence, Fig. 7, in three step to 29 ft. lbs., then mark top front side of each bolt, then tighten an additional 90°, ensuring alignment mark is facing side ward, then tighten and additional 90°, ensuring alignment mark is facing rearward.
b.Torque two front cylinder head bolts to 15 ft. lbs.
c.Torque intake bearing caps in sequence shown, Fig. 8, in three steps to 12 ft. lbs.
d.Torque exhaust bearing caps in sequence shown, Fig. 9, in three steps to 12 ft. lbs.
e.Torque cylinder head cover bolts in sequence shown, Fig. 10, to 69 inch lbs.
 

Adjuntos

  • toyota_previaLE_cylinderhead_1.jpg
    toyota_previaLE_cylinderhead_1.jpg
    83,6 KB · Visitas: 1.868
  • toyota_previaLE_cylinderhead_2.jpg
    toyota_previaLE_cylinderhead_2.jpg
    79 KB · Visitas: 814
  • toyota_previaLE_cylinderhead_3.jpg
    toyota_previaLE_cylinderhead_3.jpg
    70 KB · Visitas: 630
  • toyota_previaLE_cylinderhead_4.jpg
    toyota_previaLE_cylinderhead_4.jpg
    93,8 KB · Visitas: 446
  • toyota_previaLE_cylinderhead_5.jpg
    toyota_previaLE_cylinderhead_5.jpg
    95,6 KB · Visitas: 460
  • toyota_previaLE_cylinderhead_6.jpg
    toyota_previaLE_cylinderhead_6.jpg
    124,2 KB · Visitas: 555
  • toyota_previaLE_cylinderhead_7.jpg
    toyota_previaLE_cylinderhead_7.jpg
    87,1 KB · Visitas: 553
  • toyota_previaLE_cylinderhead_8.jpg
    toyota_previaLE_cylinderhead_8.jpg
    67,6 KB · Visitas: 532
  • toyota_previaLE_cylinderhead_9.jpg
    toyota_previaLE_cylinderhead_9.jpg
    81,7 KB · Visitas: 495
  • toyota_previaLE_cylinderhead_010.jpg
    toyota_previaLE_cylinderhead_010.jpg
    81,2 KB · Visitas: 525

El contenido de especificaciones técnicas,comentarios, opiniones y otros datos en este foro sólo son con fines informativos y son de exclusiva responsabilidad de cada usuario. Foromecanicos.com no puede y no verifica ni garantiza la exactitud o exhaustividad de la información. Usted utiliza este sitio web bajo su propio riesgo y solo con fines informativos. Las marcas y los logotipos de los fabricantes de automóviles en esta página web son propiedad de los titulares de las mismas. Usamos cookies.Si continúas utilizando este sitio, estás consintiendo utilizar cookies.
Arriba